EMF 2003-2012 Dodge Ram 2500/3500 Heavy Duty Ball Joints

7467-7460-KIT

Free Ships in 1-5 Business Days

Regular price $667.00 Save $-667.00

-653 in stock

 

Includes all 4 ball joints, Spanner Wrench and Allen Key and Upper and Lower Install Tools.  EMF steering bushings included with all joints.

Upper Ball Joints Fit:

2006-2008 Dodge Ram 1500 4WD

2003-2015 Dodge Ram 2500/3500 2WD/4WD

2007-2015 Dodge Ram 2500 2WD

2011-2018 Dodge Ram 2500HD / 3500HD

Lower Ball Joints Fit:

2006-2008 Dodge Ram 1500 4WD

2003-2012 Dodge Ram 2500/3500 2WD/4WD

2007-2012 Dodge Ram 2500 2WD

2013 Dodge Ram 2500/3500 2WD/4WD (NON-RADIUS ARM SETUP)

If you are unsure which Ball Joints your vehicle may need (Standard or Oversized), measure the ID of the hole in the knuckle or axle. The OD of the joint should be 0.002 or greater than the hole. See below for OD measurements of our products.

Facts about the EMF Ball Joint:

  • 2 Canadian and US Patents covering the design
  • Rebuildable so you will never have to purchase an entire unit again, you simply replace the inner race and pin and off you go. You can do this right on the truck without removing the housing from the knuckle
  • Serviceable so if you ever start to feel movement in the joint, you simply back out the set screw on the side of the cap and tighten the cap then replace the set screw. This can be done right on the truck without having to remove anything from the knuckle.
  • Greaseable so you can just pump a couple squirts of grease into it around every oil change and go
  • The entire unit is 100% Canadian Made by an Alberta Small Business. We have a strict Quality Assurance policy and each piece we make is numbered and logged with tolerances and measurements documented so if there is ever a problem we can look back on when it was manufactured and what the material specs were.
  • EMF is the only Ball Joint with the removable race and pin (part of our patents). Competitor products have a removable pin that can be rebuilt, however the inside of the housing will wear as the pin wears resulting in the inevitable replacement of the entire unit in the future, as the pin will no longer possess a tight fit. By having the internal race and pin set on the EMF ball joint, the race will act as the wear point instead of the housing body creating a long lasting unit.
  • EMF’s price point is set below the competitor pricing which is very enticing to the customer. We are not only a manufacturer and business, we are also the consumer so we wanted to have something affordable and high quality available.
  • Each EMF Ball Joint unit is made from 4140 HTSR material and then sent to a metal treating facility to be Nitride Coated. Liquid Salt Bath Nitriding is a second heat treating process on the material resulting in up to a 30% strength increase as well as a beautiful black oxide corrosion resistant coating that also resists galling and does not reduce the tolerances of the pieces.

 

EMF Ball Joint Warranty

  • Life-Time Warranty against Material and Manufacturers Defects. EMF will replace part of or the entire unit if it is determined to be an issue that falls under this category. The customer is encouraged to contact EMF directly to determine cause of fault and to receive warrantied products.
  • Warranty does not cover breakage due to misuse of the product, improper installation or as a result of another component failure on the vehicle.
  • EMF Ball Joints are meant to be rebuilt, which means the internal races and pin will wear over time under normal circumstances. The internal race and pin components are not covered by replacement Warranty, unless it is determined there is a manufacturer defect that caused premature wear. In order to maximize your product life, regular maintenance which includes tightening of the cap and greasing are required.

Download EMF Upper & Lower Ball Joint Instructions

Patent Document - Serviceable Ball Joint with Removable Race 15/057,2549

Customer Reviews

Based on 20 reviews
95%
(19)
0%
(0)
0%
(0)
5%
(1)
0%
(0)
C
Chris Colbert
Ball Joints

So far these EMF Ball joints seem to be doing great!! Since they are made for off road activity, regular daily driving should be a breeze.

E
Ethan Baez
EMF ball joints

these guys make a great product.. the oversized joints were a tight fit… took some patience to get them started but once they were seated they went in … it’s a good feeling knowing you don’t have to remove them just rebuild them… 💯

C
Christopher Culler
EMF Balljoints - Very Impressed

After doing extensive hours of research I landed on EMF Ball joints for my 2005 Dodge 2500. I was torn between these and the Carli but the EMF price point is what sold me in the end. If you have been researching ball joints like I did you will find many, many people recommending these for dodge trucks. They are the only fully rebuildable ball joints for our truck so once you press them in you are good. If you've done a lot of ball joints you will understand how nice that is.
I had absolutely zero issues with install, as per the instructions I tightened the ball joints up with a wrench and never had the shaft turn on me as stated in other reviews. Also if you do end up having the shaft spinning just apply pressure up or down on the knuckle as needed to lock in the shaft. The instructions and tools provided are perfect and necessary for install. They take the guess work out of everything. I could not be happier with the install process.
After getting them installed I took a test drive and am very impressed with the feeling of the truck. Turning is smoother and more precise. The ball joints I pulled out were not awful by any means but that just shows that these ball joints are a massive improvement over the Moogs I had previously installed.

A
Angel Rodriguez
Best ball joints

Best ball joints

A
Abraham Davis
ball joints

just installed, like them so far! Looks and feels like quality unit!